Προσφορά!

3 Axis CNC Kit

174.90 164.40



Κωδικός Προϊόντος : C-82018
Διαθεσιμότητα : Αμεσα Διαθέσιμο (3 - 15 ημέρες)
Στην τιμη περιλαμβανονται τα εξοδα αποστολής
Χωρίς Τελωνειακούς Δασμούς
Κωδικός προϊόντος: 32682549757 Κατηγορία:

Περιγραφή

3 Axis CNC Kit 3x Μοτέρ Nema23 & 3x Drives & Interface Board & 350W Τροφοδοτικό

Περιλαμβάνει:

  • 3 x TB6560 MD430 single axis driver
  • 3 x 23HS8430B stepper motor  (διπλός άξονας 270 Oz-in 3.0A)
  • 1 x 350W 24V/10A παλμοτροφοδοτικό
  • 1 x 5 axis breakout board
  • 1 x DB25 καλώδιο παράλληλης θύρας
  • 1 x USB καλώδιο

 

1. TB6560 MD430 Low noise of stepper motor driver

MD430 is a compact single axis bipolar 3.0A/phase stepper motor microstepping driver with step and direction inputs, DIP switch settable step mode (full, half, eight and sixteenth–S3/S4), torque (100%, 75%, 50%, 20%–S5/S6) ,work current (0-3A–SW1/SW2/SW3) and decay mode (0%, 25%, 50% and 100%).
MD430-HZ

 . Χαρακτηριστικά:

  • Single-chip motor driver for sinusoidal microstep control of stepping motors
  • Power on in indication led
  • 3Amps-34Volts(Supply voltages:12-34DC)
  • Full step, half step, eight step and sixteenth step(selection with dipswitches)
  • Torque (100%, 75%,50%, 20%)
  • Work Current (0-3A selection with SW1/SW2/SW3)
  • 4 Wire,6 Wire,8 Wire stepper motors can be used
  • Two phases bipolar driver
  • Easy wiring with standard screw terminals
  • Step frequency up to 100khz
  • Fuse protection on power supply rail(protects the board,but also your power supply and motor)

 

2.  5 axis CNC Breakout board interface adapter board

Description:

  • full support for MACH3, KCAM4, EMC2, the PC software to support parallel port control;
  • leads to all the parallel port of all 12 data transmission output pin, which can control the five stepper motor driver;
  • with 5-way input interface, you can access the limit switches and emergency stop switch, reset knife;5 input LED indicates the status of the input;
  • all the way with a 12A relay control, normally open, normally closed leads, user-friendly connection;
  • power supply with 5V USB power supply or external power supply to facilitate the access of external power supply;On the external drive enable signal amplification, filtering, enhancement processing;
  • the pulse, the direction of signal shaping, enhanced with a carrying capacity, data transmission speeds reach 10 MBit / S;
  • the output pin with extension interfaces can 2.54mm pin 2.54mmXH-Block;

Superiority:

  • the use of new imported Japanese Toshiba TB6560 chip (disguising);
  • The base used dense teeth radiator, cooling super, to ensure the stable operation of equipment;
  • the input signal using a high-speed opto-isolation to ensure not losing steps, which the pulse direction signals with the same level of 6N137, dual high-speed optocoupler;
  • a variety of semi-flow mode and the semi-flow current selection, the use of more flexible
  • Decay mode is adjustable to ensure the motor running smooth;
  • Sophisticated appearance size cooling pad size: 75mm * 65mm, four mechanical installation positioning hole size is: 67mm * 58, mounting hole diameter is 4mm
  • Set method detailed table on the board, easy to use;
  • With anti-reverse circuit, even if not careful the power plug back and will not burn the chip, the use of safer.

 

3. Stepper Motor

  • Step angle accuracy:+ – 5%(full step,not load)
  • Ακρίβεια αντοχής: + – 10%
  • Ακρίβεια επαγωγής: + – 20%
  • Ανύψωση θερμοκρασίας: 80° Max (ονομαστικό ρεύμα, 2 φάσεις σε λειτουργία)
  • Θερμοκρασία περιβάλλοντος: -20° έως +50°
  • Insulation resistance: 100ohm Min, 500VDC
  • Insulation Strength:500VAC για ένα λεπτό

23HS8430B, εμπρός άξονας έχει διάμετρο 8mm, 21mm μήκος, ο πίσω άξονας έχει διάμετρο 6,35mm και μήκος 10mm, ροπή συγκράτησης 270oz-in ή 18kg.cm

57motor 8mm dra

Σύνδεση:

A+ A- B+ B-
RED GREEN YELLOW BLUE

 

 

4.  Παλμοτροφοδοτικό 350W

  • Είσοδος: 100-120VAC ή 200-240VAC, 50 / 60Hz
  • Έξοδος:  24v / 14.5 A

 


 

Επιπρόσθετες Πληροφορίες

Βάρος 5.6 kg
Διαστάσεις 35 x 30 x 25 cm
Motor Holding Torque

270 oz-in/180N.cm

Motor Model Number

23HS8430B/TB6560

Motor Step Angle(degrees)

1.8

Motor Current / Phase

3A

Drive

TB6560 MD430

Drive Voltage

12~34V

Drive Microstep

256 microstep

Drive Current

3.5A

Motor wire

4pcs

Motor size

57x57x76mm

Breakout board

5Axis CNC breakout board

Power supply

350W 24V 14.5A

Αξιολογήσεις

Δεν υπάρχει καμία αξιολόγηση ακόμη.

Δώστε πρώτος μία αξιολόγηση “3 Axis CNC Kit”

Η ηλ. διεύθυνση σας δεν δημοσιεύεται. Τα υποχρεωτικά πεδία σημειώνονται με *

0