Παλμογράφος Hantek DSO4102C

320.40



Κωδικός Προϊόντος : C-89705
Διαθεσιμότητα : Αμεσα Διαθέσιμο (3 - 15 ημέρες)
Στην τιμη περιλαμβανονται τα εξοδα αποστολής
Χωρίς Τελωνειακούς Δασμούς
Κωδικός προϊόντος: 32818141888 Κατηγορίες: ,

Περιγραφή

Χαρακτηριστικά:

  • Model: DSO4102C
  • 2 Channel Digital Oscilloscope & Arbitrary/Function Waveform Generator & Synchronizing Signal & External Trigger
  • Support SD card, VGA function (optional)
  • Integrated USB Host, Support USB disk storage, USB interface/SD card system update
  • 32 kinds of Automotive measurement, with FFT function;
  • Real-Time Sample: 1GSa/s 
  • Equivalent Sample Rate: 25GSa/s

Acquisition Modes:

  • Normal: Normal data only
  • Peak Detect: High – frewuency and randin glith capture
  • Average: Waveform Average, selectable 4, 8, 16, 32, 64, 128

Inputs:

  • Input Coupling:  DC, AC, and GND
  • Input Impedance: 1MΩ ± 2%, | 20pF ± 3pF 
  • Probe Attenuation: 1X, 10X
  • Supported Probe Attenuation Factor: 1X, 10X, 100X, 1000X,
  • Max Input Voltage:
    • CAT I and CAT II: 300VRMS (10x)
    • CAT III: 150VRMS (1x)
    • Installation Categoty II: derate at 20dB/decade above 100kHz to 13V peak AC at 3 MHz* and above. For non- sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed though AC coupling must be limited to 300V. If these values are excee, damage, to the oscilloscope may occur.

Horizontal:

  • Sample Rate: 1GS/s 
  • Waveform Interpolation: (sin x) / x
  • Record length: 40K
  • SEC/DIV Range: 4ns/div to 40s/div
  • Sample Rate and Delay Time Accuracy: ±50ppm (at over  ≥ 1ms time interval)
  • Position Range:
    • 20ns/div to 80us/div, (-8div x s/div) to 40ms 
    • 200us/div to 40s/div, (-8div x s/div) to 400s
  • Delta Time Measurement Accuracy (Full Bandwidth):
    • Single-shot, Normal mode: ±(1 sample interval + 100ppm x reading + 0.6ns)
    • >16 average: ±(1 sample interval + 100ppm x reading + 0.4ns)
    • Sample interval = s/div ÷ 200

Vertical:

  • Vertical Resolution (A/D): 8 bits resolution, all channel sampled simultaneously
  • Position Range: 2mV/div to 10V/div
  • Bandwidth: 100MHz
  • Rise Time at BNC (typical): 3.5ns
  • Analog Bandwidth in Normal and Average modes atBNC or with probe, DC Coupled:
    • 2mV/div to 20mV/div, ± 400mV | 50mV/div to 200mV/div, ±1V
    • 500mV/div to 2V/div, ± 40V | 5V/div, ± 50V
  • Math: +, -, ×, ÷, FFT
  • FFT: Windows : Hanning, Flatop, Rectamgular, Bartlett, Blackman | 1024 Sample point
  • Bandwidth Limit: 20MHz
  • Low Frequency Response (-3db): = 10Hz at BNC
  • DC Gain Accuracy:
    • ±3% For Normal or Average acquisition mode, 5V/div to 10mV/div
    • ±4% For Normal or Average acquisition mode, 5mV/div to 2mV/div
  • DC Measurement Accuracy:  When vertical displacement is zero, and N = 16 ± (3% x reading + 0.1 div + 1mV) only 10mV/div or greater is selected
  • Average Acquisition Mode: When vertical displacement is not zero, and N = 16:± [3% x (reading + vertical position) + 1% of vertical position + 0.2 div] Add 2mV for settings from 2mV/div to 200mV/div | Add 50mV for settings from 200mV/div to 5V/div
  • Volts Measurement Repeatability, Average Acquisition Mode: Delta volts between any two averages of = 16 waveforms acquired under same setup and ambient conditions 

Trigger System:

  • Trigger Type: Edge, Video, Pulse, Slope, Over time, Alternative
  • Trigger Sourse: CH1, CH2, EXT, EXT/5, AC Line
  • Trigger Modes: Auto, Normal, Single
  • Coupling Type: DC, AC, Noise Reject, HF Reject, LF Reject 
  • Trigger Sensitive (Edge Trigger Type):
    • DC (CH1, CH2): 1 div from DC to 10MHz 1.5div from 10MHz to 100MHz 2div from 100MHz to full
    • DC (EXT): 200mV from DC to 100MHz | 350mV from 100MHz to 200MHz
    • DC (EXT/5): 1V from DC to 100MHz | 1.75V from 100MHz to 200MHz
    • AC: Attenuates signals below 10Hz
    • HF Reject: Attenuates signals above 80kHz
    • LF Reject: Same as the DC – cou limits for Frequencies above 150kHzAttenuates signals below 150kHz
  • Trigger Level Range: 
    • CH1 / CH2:  ± 8 divisions from center of screen
    • EXT: ± 1.2V
    • EXT/5: ± 6V
  • Trigger Level Accuracy (typical)  Accuracy is for signals having rise and fall times = 20ns: 
    • CH1 / CH2:  0.2div x volts/div within ± 4 divisions from center of screen 
    • EXT: ± (6% of setting + 40mV) 
    • EXT/5: ± (6% of setting + 200mV)
  • Set Level to 50% (typical): Operates with input signals  = 50Hz

Video Trigger:

  • Video Trigger Type:
    • CH1, CH2: Peak to Peak amplitude of 2 divisions
    • EXT: 400mV
    • EXT/5: 2V 
  • Signal Formats and Field Rates, Video Trigger Type: Supports NTSC, PAL and SECAM broadcast systems for any field or any line 
  • Holdoff Range: 100ns ~ 10s

Pulse Width Trigger:

  • Pulse Width Trigger Mode: Trigger when (<,>,= or ≠) Positive pulse or Negative pulse
  • Pulse Width Trigger Point:
    • Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level.
    • Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width.
    • Less than: The triggers point is the trailing edge.
    • Greater than (also called overtime trigger):  The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width.
  • Pulse Width Range: 20ns ~ 10s

Slope Trigger:

  • Slope Trigger Mode: Trigger when (<,>,= or ≠) | Positive slope or Negative slope
  • Slope Trigger Point:
    • Equal: The oscilloscope triggers when the waveform slope is equal to the set slope.
    • Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope.
    • Less than: The oscilloscope triggers when the waveform slope is less than the set slope.
    • Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.
  • Time range: 20ns ~ 10s

Alternative Trigger:

  • Trigger on CH1: Internal Trigger :Edge, Video, Pulse, Slope, Winth
  • Trigger on CH2: I nternal Trigger :Edge, Video, Pulse, Slope, Winth

Trigger Frequency Counter:

  • Readout Resolution: 6 digits
  • Accuracy: ±30ppm (including all frequency reference errors and ± 1 count errors)
  • Frequency Range: AC coupled, from 4Hz minimum to rated bandwidth
  • Signal Source:
    • Pulse Width or Edge Trigger modes: all available trigger sources
    • The Frequency Counter measures trigger source at all times, including when the oscilloscope measurement window that quality as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time
    • Edge Trigger mode: The oscilloscope counts all adges of sufficient magnitude and correct polarity
    • Video Trigger mode: The Frequency Counter does not work

Measure:

  • Cursor Measurement:
    • Voltage difference between cursors: △V
    • Time difference between cursors: △T
    • Reciprocal of △T in Hertz (1/△T)
  • Auto Measurement:  Frequency, Period, Mean, Pk-Pk, Cycli RMS, Max, Min, Rise time, Fall Time, + Pulse Width, – Pulse Width, Delay 1-2 Rise, Delay 1-2 Fall, +Duty, -Duty, Vbase, Vtop, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF

Signal Source Mode:

  • Waveform Impedance: DC – 25MHz
  • Sample Rate: 200MHz DDS
  • Output Waveform: Arbitrary wave / square wave / sine wave / triangle wave / trapezoidal wave / pulse  wave / DC
  • Frequency Resolution: 0.10 %
  • Waveform Depth: 2KSa
  • Vertical Resolution: 12 bit
  • Frequency Stability: < 30ppm
  • Waveform Range: -3.5V ~ +3.5V
  • Output Impedance: 50C
  • Output Current: 50mA peak = 100mA
  • System BW: 25M
  • Harmonic Distortion: -50dBc (1KHz) -40dBc (10KHz) 

General Features

Display:

  • Display type: 7″ TFT 64K color (diagonal liquid crystal)
  • Display Resolution: 800 x 480 pixels
  • Display Contrast: Adjustable (16 gears) with the progress bar

Probe Compensator Output:

  • Output Voltage (typical): About 5Vpp into = 1MC load
  • Frequency (typical):1kHZ

Power supply:

  • Supply Voltage:
    • 100 – 120VACRMS (± 10%), 45Hz to 440Hz, CAT II
    • 120 – 240VACRMS (± 10%), 45Hz to 660Hz, CAT II
  • Power Consumption: <30W
  • Fuse: 2A, T rating, 250V

Environmental:

  • Temperature:
    • Operating: 0°C to 50°C
    • Non Operating: -40°C to +71°C
  • Cooling Method: Convection
  • Humidity:
    • +40°C or below: = 90% relative humidity
    • +41°C to 50°C: = 60% relative humidity
  • Altitude
    • Operating: Below 3,000m 
    • Non Operating: Below 15,000m 

Mechanical:

  • Size: 385 x 200 x 245 mm (LxWxH)
  • Net Weight: 2.08KG
  • Weight: 3.5KG

 

 


 

Επιπρόσθετες Πληροφορίες

Βάρος 3.5 kg
Διαστάσεις 38 x 19 x 24 cm
Max Waveform Capture Rate

30,000wfm/s

Digital Channels

2

IS Battery Demountable

No

Αξιολογήσεις

Δεν υπάρχει καμία αξιολόγηση ακόμη.

Δώστε πρώτος μία αξιολόγηση “Παλμογράφος Hantek DSO4102C”

Η ηλ. διεύθυνση σας δεν δημοσιεύεται. Τα υποχρεωτικά πεδία σημειώνονται με *

0